Proflex FIA fuel bladder tank for the Ferrari 430
BUYING GUIDE

FIA Fuel Bladder Cells vs Alloy Fuel Tanks: Which Does Your Car Need?

A bespoke Kevlar safety cell or a baffled alloy tank? Here is how each one works, what the FIA rules actually say, and how to pick the right one for your car and your championship.

By Race Rally Supplies · 7 minute read

The fuel tank is one of the most important safety parts on a competition car, and one of the most misunderstood. Get it wrong and you either fail scrutineering or, far worse, carry a tank that splits in an accident. Get it right and you also cure fuel surge, save weight and free up space. This guide covers the two main routes: an FIA-homologated bladder cell and an alloy baffled tank.

5 years
life of an FT3 bladder from the date of manufacture
+2 years
extra if re-inspected and re-certified by the maker, 7 years max
£121.99
entry point for an obp alloy baffled tank

Bladder cell or alloy tank: what is the difference?

SAFETY CELL
FIA fuel bladder

A flexible bag made from reinforced fabric (Proflex use their Kevlar PROFLEXCELL material). In an impact it deforms rather than splitting, which is why the FIA demands one in most international and many national classes.

  • Required where your regs say FT3, FT3.5 or FT5
  • Made to fit almost any space
  • Limited life: 5 years, extendable to 7
ALLOY TANK
Baffled alloy tank

A welded aluminium tank with internal baffles to stop fuel sloshing away from the pickup. Simple, tough, lower cost and available off the shelf.

  • Common in club, kit car, autograss and historic classes
  • No expiry date
  • Not a substitute where an FIA cell is required
💡 Start with your regulations

Before you buy anything, check your championship and class regulations. If they ask for an FIA FT3 (or higher) safety tank, an alloy tank will not pass scrutineering, however well it is made. If they allow a non-FIA tank, alloy is often the sensible, lower-cost choice.

How an FIA bladder cell protects you

01
ContainThe reinforced bladder flexes and absorbs impact instead of tearing open like a rigid tank can.
02
ControlSafety foam inside the cell cuts slosh and surge, and helps suppress vapour in an accident.
03
ProtectAn alloy container or carbon cover around the bladder shields it from debris and holds its shape in the car.

The FIA rules in plain English

FIA safety bladders are homologated to one of three standards: FT3-1999, FT3.5-1999 or FT5-1999. FT3 is the baseline most regulations ask for; FT3.5 and FT5 are tougher grades used in higher categories. The FIA has also introduced a newer tank standard, FIA 8875-2025, which now appears alongside FT3, FT3.5 and FT5 in some Appendix J regulations.

LIFE
5 years from manufacture
No bladder may be used beyond 5 years from its manufacture date unless it is re-inspected and re-certified by the manufacturer.
+2
Re-certification
After re-inspection the maker can extend it for up to 2 more years, but never beyond 7 years from the date of manufacture.
LABEL
Keep the label visible
Scrutineers need to see the FIA label, so any container or cover needs an opening that lets them check it.

Proflex bespoke FIA bladder cells

Proflex FIA fuel bladder tank for the Lola T70Proflex make FIA-homologated (FT3-1999) bladder cells in the UK from their lightweight Kevlar PROFLEXCELL material. Every tank is made to order, in any size and shape, from a simple box tank to a fully contoured cell that wraps around a specific chassis. They already hold thousands of existing designs and templates.

Cars Proflex have built for include the Lola T70, Ferrari 430 and 550 GT1, Ford GT40, Porsche 996, 997 and 991, Aston Martin Vantage GT2 and GT3, Lamborghini Huracan Super Trofeo EVO, Ford Focus WRC, Classic Mini, Mini Miglia, Ginetta G50, Cosworth RS500 and Ligier LMP2 and LMP3.

Proflex FIA bladder tank · Request a quote →

Containers and covers

TOUGH
Alloy container

A custom-fabricated alloy box that contours and supports the bladder and protects it from debris and sharp edges.

Request a quote →
LIGHT
Carbon cover

A made-to-fit carbon cover that does the same job as the alloy box with less weight, ideal for cars built to a weight limit.

Request a quote →

Servicing: Proflex can strip, inspect and rebuild a bladder at their factory, fitting new Viton gaskets to each nut ring, and can re-certify it at the 5-year point for a further 2 years.

obp alloy baffled tanks

obp V2 8 gallon alloy fuel tank with built-in fuel pumpsWhere your regulations allow an alloy tank, obp make one of the widest off-the-shelf ranges in the UK. Every tank is welded aluminium with internal baffles, and you choose between barbed fittings for simple push-on hose or JIC/AN fittings for braided lines.

The V2 range goes further, with tanks designed to take in-tank pumps or supplied with them already fitted, which removes the need for a separate swirl pot and lift pump on many cars.

L1
Universal baffled tanks from £121.99
2 to 8 gallons, barbed or JIC/AN. Alloy baffled tank · 6 gallon JIC/AN · Kit car tank
L2
Car-specific tanks from £310.99
Direct-fit replacements for the Ford Escort MK1/MK2 boot floor. Escort MK1/MK2 tank · V2 Escort tank
L3
Tanks with built-in pumps from £450.99
Pumps inside the tank for a neater, surge-free system. 10x6" cluster unit · V2 8 gallon · V2 Escort

Finish the job: foam, surge and sender

FIA tank foam · from £5.99 Universal fuel sender · £42.99 2.5L surge tank · £452.99 Swirl pots

Side by side

Proflex FIA bladder obp alloy baffled tank
FIA homologated ✔ FT3-1999 ✘
Construction Flexible Kevlar bladder Welded aluminium, baffled
Shape Any size, made to fit Standard sizes and Escort fit
Lifespan 5 years, up to 7 with re-cert No expiry
Lead time Made to order Off the shelf
Best for FIA, GT, endurance, rally, historic FIA Club, kit car, autograss, historic
Price On application from £121.99

Quick pick

"My regs say FIA FT3 safety tank"
"I'm building a club car and an alloy tank is allowed"
"I've got a MK1 or MK2 Escort"
"I'm getting fuel starvation in long corners"

Five things to get right when fitting a tank

  1. 1Read your regs first. Check whether you need an FIA tank, where it may be mounted and whether it must be separated from the cockpit.
  2. 2Size it for the longest stint. Work out your fuel use per lap or stage, add a safety margin, and do not carry more weight than you need.
  3. 3Plan for surge. Baffles and foam help, but a hard-cornering car on low fuel usually needs a swirl pot or in-tank pumps as well.
  4. 4Vent and bond it properly. Fit the venting and non-return valves your regs ask for, and make sure metal fuel system parts are electrically connected to the shell.
  5. 5Diary the expiry date. An FIA bladder past its date will be turned away at scrutineering. Book re-certification before year 5, not after.

Common questions

Can I use an alloy tank instead of an FIA bladder?

Only if your regulations allow it. Where an FIA FT3 (or higher) tank is required, an alloy tank will not be accepted, even with foam fitted.

How long does an FIA bladder last?

Five years from manufacture. The manufacturer can re-inspect and re-certify it for up to two more years, to a maximum of seven years from the date it was made.

Why are Proflex tanks priced on application?

Every Proflex tank, container and cover is made to order, so the price depends on size, shape and fittings. Request a quote with your car and requirements and we will come back to you with a price and lead time.

My car isn't on the Proflex list. Can they still make a tank?

Yes. Choose Other / bespoke design on the product page and tell us the car, the space available and the capacity you need.

Do I need foam in an alloy tank?

It is not always compulsory, but FIA-compliant foam reduces slosh and surge and is cheap insurance. Check your class regulations, as some require it.

Still not sure?

Tell us your car, your class and the space you have and we will point you to the right tank, or get a Proflex quote moving for you.

📞 Call 0333 444 4304 FIA bladder tanks Alloy fuel tanks
Back to blog